- 您现在的位置：买卖IC网 > Sheet目录222 > DS1985-F3+ (Maxim Integrated)IBUTTON 16KBit ADD-ONLY F3
DS1985
EXTENDED READ MEMORY [A5H]
The Extended Read Memory command supports page redirection when reading data from the 16384-bit
EPROM data field. One major difference between the Extended Read Memory and the basic Read
Memory command is that the bus master receives the Redirection Byte first before investing time in
reading data from the addressed memory location. This allows the bus master to quickly decide whether
to continue and access the data at the selected starting page or to terminate and restart the reading process
at the redirected page address. A non-redirected page is identified by a Redirection Byte with a value of
FFH (see description of EPROM Status Bytes). If the Redirection Byte is different than this, the master
has to complement it to obtain the new page number. Multiplying the page number by 32 (20H) results in
the new address the master has to send to the DS1985 to read the updated data replacing the old data.
There is no logical limitation in the number of redirections of any page. The only limit is the number of
available memory pages within the DS1985.
In addition to page redirection, the Extended Read Memory command also supports “bit-oriented”
applications where the user cannot store a 16-bit CRC with the data itself. With bit-oriented applications
the EPROM information may change over time within a page boundary making it impossible to include
an accompanying CRC that will always be valid. Therefore, the Extended Read Memory command
concludes each page with the DS1985 generating and supplying a 16-bit CRC that is based on and
therefore always consistent with the current data stored in each page of the 16384-bit EPROM data field.
After having sent the command code of the Extended Read Memory command, the bus master follows
the command byte with a 2-byte address (TA1=(T7:T0), TA2=(T15:T8)) that indicates a starting byte
location within the data field. By sending eight read data time slots, the master receives the Redirection
Byte associated with the page given by the starting address. With the next sixteen read data time slots, the
bus master receives a 16-bit CRC of the command byte, address bytes and the Redirection Byte. This
CRC is computed by the DS1985 and read back by the bus master to check if the command word, starting
address and Redirection Byte were received correctly.
If the CRC read by the bus master is incorrect, a Reset Pulse must be issued and the entire sequence must
be repeated. If the CRC received by the bus master is correct, the bus master issues read time slots and
receives data from the DS1985 starting at the initial address and continuing until the end of a 32-byte
page is reached. At that point the bus master will send 16 additional read time slots and receive a 16-bit
CRC that is the result of shifting into the CRC generator all of the data bytes from the initial starting byte
to the last byte of the current page.
With the next 24 read data time slots the master will receive the Redirection Byte of the next page
followed by a 16-bit CRC of the Redirection Byte. After this, data is again read from the 16384-bit
EPROM data field starting at the beginning of the new page. This sequence will continue until the final
page and its accompanying CRC are read by the bus master.
The Extended Read Memory command provides a 16-bit CRC at two locations within the transaction
flow chart: 1) after the Redirection Byte and 2) at the end of each memory page. The CRC at the end of
the memory page is always the result of clearing the CRC generator and shifting in the data bytes
beginning at the first addressed memory location of the EPROM data page until the last byte of this page.
The CRC received by the bus master directly following the Redirection Byte, is calculated in two
different ways. With the initial pass through the Extended Read Memory flow chart the 16-bit CRC value
is the result of shifting the command byte into the cleared CRC generator, followed by the two address
bytes and the Redirection Byte. Subsequent passes through the Extended Read Memory flow chart will
generate a 16-bit CRC that is the result of clearing the CRC generator and then shifting in the Redirection
Byte only.
12 of 26
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
DS1990A-F3+
IC IBUTTON SERIAL NUMBER F3
DS1990R-F5#
IBUTTON SERIAL NUMBER F5
DS1993L-F5+
IBUTTON MEMORY 4KBit F5
DS1995L-F5+
IBUTTON MEMORY 16KBit F5
DS1996L-F5+
IBUTTON MEMORY 64KBit F5
DS9092K#
KIT IBUTTON STARTER
DS9502P+T&R
DIODE ESD PROTECTION 6-TSOC
DS9503P+
DIODE ESD PROTECTION W/RES 6TSOC
相关代理商/技术参数
DS1985-F5
功能描述:iButton RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1985-F5#
功能描述:iButton RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1985-F5+
功能描述:iButton 16Kb Add-Only iButton RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1985U
制造商:未知厂家 制造商全称:未知厂家 功能描述:UniqueWare iButton
DS1985U-F5-117D+
功能描述:iButton
RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1986
制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:64-kbits Add-Only iButton⑩
DS1986+F3
制造商:Maxim Integrated Products 功能描述:ADD-O IBTN 64KB, F3 (GENERIC) LFREE - Rail/Tube
DS19860-F3-W
功能描述:iButton
RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated